99热在线精品观看-99热在线精品免费播放6-99热在线看-99热在线免费-99热在线免费播放-99热在线免费观看

Professional smart display solution provider
Focused on manufacturing large display screens for 15 years, providing door-to-door services nationwide

Hotline

0755-29595688

Common problem

Service

Position:

Home > Service > Common problem

Common problems and solutions during the use of splicing screens

Author:admin / Publication time:2019-06-19

1、 The image feels covered with a layer of colorful watercolor

This issue occurred because the splicing box program did not pair correctly with the screen, mostly between LG and Samsung

Mixing or burning the wrong program for screen splicing can be solved by entering the factory menu and modifying TI;


2、 The image has multiple colors of red, green, blue, and white that alternate every few seconds

There are two possibilities for this issue to occur:

1. The screen cable and splicing box program are not paired correctly with the screen, please match according to the actual situation;

2. The splicing box is currently in baking machine mode, and can be changed to off status when entering the factory menu;

3、 Image font blurry, drawback


This problem usually occurs when the high-definition screen AB group is reversed, which can be modified to the correct setting in the factory menu;

4、 The screen is black, the back is shiny


There are multiple possibilities for this issue to occur:

1. The splicing box program is paired incorrectly with the screen being used. Please match according to the actual situation;

2. Incorrect installation and pairing of screen cables; (For example, AN01 is prone to installation errors for individual customers, while Samsung LG is high)

Clear screen cables are easy to use incorrectly

3. Static electricity damages the splicing box IC, resulting in hardware failure of the splicing box; (Can be alternately checked and confirmed)

5、 Splicing box cannot be controlled


There are multiple possibilities for this issue to occur:

1. The USB to serial driver is not installed correctly or the cable cannot work;

2. The splicing software did not set the correct serial port or did not select the corresponding address for control;

3. The splicing box uses a soft ID; (You can make the software splicing unit 15X15 for control attempts or

Control in the corresponding grid of the soft ID, or use the callback code hardware address after factory reset

4. Use an adapter from another company; (Definition may vary)

5. Not plugged into RJ45-IN; (Re inspection and troubleshooting)

6. There is a problem with the environment; (alternating investigation)

7. The network cable is faulty; (alternating investigation)

8. The dialing code was not dialed or not dialed to the end, not dialed correctly; (Re inspection and troubleshooting)

6、 How to enter the factory menu


Remote control: MENU ->PICTURE ->FREEZE;

Software: After entering debugging mode, there are relevant settings on the debugging tab on the left side of the software's main interface;


7、 Definition of adapter

Turn the 3 (TX) and 5 (GND) of the serial port into the orange (2-pin TX) and blue white (5-pin GND) of the Ethernet cable;

8、 Image not full screen


This problem is caused by multiple reasons and needs to be investigated step by step:

1. Replace VGA cable (if only one screen is not full, you can confirm by swapping)

2. Display device driver installation error, non-standard output (update driver or replace computer with driver sprite software)

Confirmation)

3. Insufficient bandwidth of the distributor or unstable voltage of the adapter (also affected by the electricity environment).

4. Software optimization (set VGA filtering to high in the settings on the left side of the software main interface, and then automatically adjust it again;

Use software like NEST to capture the screen)

9、 Phenomena after the expiration of the time limit

1. Before expiration, without any prompts, consistent with normal use;

2. When there are still three hours left, the bottom right corner of the splicing screen will periodically pop up a disappearing reminder;

3. After the time has completely expired, the image has no display, a blue screen, cannot be controlled, and the prompt in the bottom right corner is always present;


10、 How to determine whether the serial port is working after expiration


The splicing box has a protection mechanism, which can be powered off first and then on. Then, click on the information next to registration, and the communication will expire normally

Wake up and it will flash. If there is no movement, the serial port setting or connection is abnormal;

Online Service

8:00-24:00

Tel
Tel

0755-29595688

Mailbox
Mailbox

szdetian@163.com

主站蜘蛛池模板: 最近中文字幕在线 | 中文 | a级大片在线观看 | 青青免费视频在观线看 | 久久精品在线视频 | 免费观看a视频 | 天天做天天爱天天爽 | 久久乐国产综合亚洲精品 | 激情综合在线 | 狠狠躁夜夜躁人人爽天天不 | 国产成人丝袜美女厕所视频 | 成人在线观看不卡 | 人人澡人摸人人爽歪歪 | 国产日本高清 | 999久久久国产精品 999久久久精品视频在线观看 | 手机看片福利盒子久久 | 大学生久久香蕉国产线看观看 | 中文字幕在线网 | 久久精品伊人 | 久久国产精品视频 | 91中文字幕在线 | 国产精品_国产精品_国产精品 | 亚洲欧洲国产精品你懂的 | 国产精品片 | 久久婷婷久久一区二区三区 | 亚洲欧美日韩国产制服另类 | 伊人久久天堂 | 国产人成高清视频观看 | 亚洲伊人tv综合网色 | 久久综合一区 | 91免费在线看 | 在线免费观看日韩 | 国产成人91高清精品免费 | 国产边打电话边做对白刺激 | 日日夜夜天天 | 成年人免费观看网站 | 亚洲福利视频精选在线视频 | 国产精品视频一区二区三区 | 久久精品国产半推半就 | 女网址www女| 欧美成视频 | 青青青亚洲精品国产 |